|
| |
Prices for the 3-model Stanton SPS5 range & other temperature controllers are shown on this page.
Down-loadable user handbooks & datasheets for each model in the SPS5 range are also
available. An optional internal over-temperature trip module is
available for this range. Controller cables can be found in the Ancillary Equipment section.
The Stanton SPS5 Range
Common Features
- Alphabetic display for user-friendly operation
- Status display shown during firing
- Attractive wall-mounted enclosure sealed to IP65
- Control range up to 1310°C
- Delayed start facility
- R,K,N & S thermocouple types (field selectable)
- Thermocouple burn-out detection
- Heater element failure detection
- Continuous self-checking of internal operation
- Intelligent power-failure recovery
- Year 2000 compliant
- Optional internal over-temperature trip module (field installable)
|
 |
Model Features
Model
|
Description
|
Price £ Sterling
|
| SPS5.1 |
This is a fully adjustable 2-stage temperature controller. The
first stage is slow heating to an intermediate temperature t1, where the rate of rise of
temperature to t1 is settable by the user in the range 20 to 240°C/hour in 20°C/hour
steps. The second stage is heating at full power to the top temperature t2.
The controller dwells for a soak period at t2 then turns heating power off for natural
cooling. Both t1 & t2 are user-settable in the range 0 to 1310°C. The
soak period is user-settable from zero to 99 hrs. 59 mins. |
216 |
| SPS5.2 |
This is a pre-programmed 2-stage kiln temperature controller with 10 pre-set
programs. The first stage is heating to intermediate temperature t1 via a slow
ramp. The second stage is heating to the top temperature t2 via a faster ramp.
The controller then soaks at t2 if required then turns heating power off for natural
cooling. Temperatures t1, t2 & the soak period are determined by the selected
program. Top temperature t2 can be user-trimmed by ±100°C if required. |
240 |
| SPS5.7 |
This is a fully-programmable multi-stage 10 program controller. Each
program can have up to 9 ramps & nine soaks. Ramps may be heating or cooling
with ramp rates in the range 1°C/hr to 998°C + full. Up to 9 programs can be
linked in any order for very complex firings. |
280 |
| SPS5.7A |
This is a variant of the SPS5.7 fitted with an auxilliary control relay
output. This output can be configured as a damper control, event control or
over-temperature alarm. |
324 |
| SPS8i |
Optional internal over-temperature trip module. |
60 |
Over-Temperature Trip Module
|
| The SPS8i is an independent over-temperature trip module
designed solely for internal fitment to the SPS5 range of controllers. It is an
optional safety device designed to protect kilns from over-firing. It behaves like a
resettable heat fuse. Operation of the trip is indicated by an otherwise hidden
'FAULT' legend on the controller front panel |
|
 |
Data Area
| More data is available by clicking on the model numbers below. The
datasheets & handbooks available below are in Adobe Acrobat (pdf) format. You
will need the Adobe Reader to view them. If you do not already have this then it is
available here. |
 |
Other Controllers Stocked
Model
|
Description
|
Price£ Sterling
|
| ST301 |
Indicating 2-stage single program controller |
160 |
| ST301A |
Indicating 2-stage single program controller with aux. relay |
187 |
| CPC4015L |
Programmable controller |
285 |
| CPC302 |
Programmable controller (3 zone) |
650
|
Note: All prices are ex-works and exclude V.A.T.
|
